How the maths works
Every number this calculator uses is listed below, along with where it came from. Nothing is hidden, because a planning tool you cannot check is not much use — if a figure looks wrong for your lights, you need to be able to see which one it is and change it.
The figures that are fixed
100 mini lights per vertical foot of tree. This is the standard trade rule of thumb, published by Home Depot in its Christmas lights buying guide and repeated by 1000Bulbs. Home Depot gives 50 C7 bulbs per vertical foot as the equivalent figure for the larger bulb, and says to use half the number on thin trees. 1000Bulbs suggests 200 mini lights per vertical foot for a brighter look. Those three positions are exactly what the three density settings in the calculator do.
C6 and C9 counts. Home Depot lists 600 to 700 C6 bulbs and 500 to 600 C9 bulbs for a 9-foot tree. Divided by nine, that is roughly 72 and 60 bulbs per vertical foot, which is what the calculator uses.
1,800 watts on a 15 amp circuit, 2,400 on a 20 amp circuit. This is Ohm's law at 120 volts: 15 × 120 = 1,800.
80% of that as the working limit. The National Electrical Code treats a load running three hours or more as a continuous load, and a circuit should not carry more than 80% of its rating continuously. That gives 1,440 watts on a 15 amp circuit and 1,920 on a 20 amp circuit. Christmas lights on a timer run for far more than three hours, so this is the figure that matters, not the headline rating.
Three sets of incandescent lights. The Consumer Product Safety Commission's holiday safety guidance says never to string together more than three sets of incandescent lights, and its printed decoration safety sheet says to use no more than three standard-size sets per single extension cord. Those are two slightly different rules and the calculator mentions both, because they are commonly merged into one and misquoted.
The figures you can change
Watts per bulb. The calculator fills in a typical draw — 0.4 W for an incandescent mini, about 5 W for a C7 and 7 W for a C9, and a fraction of a watt for the LED equivalents. These are typical, not universal. The real figure is printed on your box, and LED strings in particular vary between manufacturers by a factor of two or more. Overwrite the field and the whole result updates.
Bulbs per string and the length of one string. There is no standard here. A 100-bulb mini string might be 20 feet or 25 feet of lit length depending on spacing, and that changes how many boxes you need. Both fields are yours to set from the packaging.
Spacing between turns, when wrapping. A trunk wrapped at 3-inch intervals looks dense; at 6 inches it looks sketched in. No source gives a correct answer because there isn't one — it is a matter of taste, and the calculator treats it as geometry rather than a rule: turns equal height divided by spacing, and each turn uses one circumference of string.
Shrub spread. A broad shrub takes more light than a narrow one of the same height, and the per-vertical-foot rule alone cannot know which you have. The spread setting is an adjustment you choose, clearly labelled as such, not a published standard.
What the calculator does not account for
- The lead wire. String lights have unlit cable at the plug end. The calculator works in lit length, so measure or read the lit length from the box, not the overall length.
- Getting power to the display. Extension cord runs are not included in the length. Add them separately, and use outdoor-rated cord outdoors.
- Voltage drop on long runs. Over a long chain of strings the far end draws slightly less and looks slightly dimmer. It does not change the planning arithmetic, but it is a real effect.
- Anything other than 120 volts. The circuit check assumes North American household supply. If you are on a 230 V supply, the wattage total is still correct but the circuit limits are not.
If a figure disagrees with your box
The box wins. Every safety-tested light string carries a label stating its own maximum connected load, and a manufacturer who has tested a specific product knows more about it than any rule of thumb. The point of a calculator is to get you close enough to buy the right amount — not to override the people who made the lights.