Free calculator · No sign-up · Works on your phone

Christmas Glow Decor

Home → Guides

C7 vs C9 vs mini Christmas lights — sizes explained

What the C numbers mean, the physical size of each bulb, how many you need per foot of tree, what each one draws, and which belongs on a roofline versus a tree.

A pile of loose coloured Christmas bulbs on green garland

Some links on this page are Amazon affiliate links. If you buy through them we may earn a commission at no extra cost to you. It does not change what we recommend.

The "C" numbers are bulb shape and size codes, not brightness ratings. The number is the bulb's diameter in eighths of an inch at its widest point: a C7 is seven eighths of an inch across, a C9 is nine eighths — just over an inch. C6 is six eighths, three quarters of an inch.

Mini lights are not part of that series at all. They are the small push-in-socket bulbs about the size of a grain of rice, and the only common Christmas light sold by shape rather than C-number.

The four sizes side by side

Mini C6 C7 C9
Bulb width tiny 3/4 in 7/8 in 1 1/8 in
Shape teardrop small cone night-light cone large cone
Typical spacing on string 2.5–6 in 6–8 in 8–12 in 12 in
Per vertical foot of tree 100 about 72 50 about 60
Incandescent watts per bulb about 0.4 — about 5 about 7
LED watts per bulb under 0.1 under 1 under 1 under 1
Usual home trees, wreaths, garland small trees, railings indoor trees, windows rooflines, outlines

The mini and C7 per-foot figures are Home Depot's published guidance. The C6 and C9 figures are worked back from the counts it lists for a 9-foot tree — 600 to 700 C6 and 500 to 600 C9.

C9 needing more bulbs per foot than C7 reads like a contradiction. It is not: these are counts of bulbs on commercial strings with different spacing, not a property of the bulbs.

Run your own numbers

The calculator does the arithmetic on this page for your own measurements — trees, rooflines, columns, railings, shrubs and windows.

Open the calculator

Which goes where

Mini lights for trees, garland and anything you want to look lit rather than decorated. Close spacing fills a tree with light instead of dotting it. Almost every indoor tree uses them.

C9 for rooflines. This is the classic American outline look. Big bulbs at one-foot spacing read clearly from the street, and because there are fewer of them per foot, the wattage total for a long run stays manageable. Mini lights on a roofline from fifty feet away look like a fuzzy line rather than lights.

C7 for windows, small trees and indoor nostalgia. It is the night-light bulb — a smaller, softer version of the C9 look. Often used where C9 would feel oversized.

C6 for railings, small outdoor trees and tight detail. A compromise size, mostly sold as LED, that suits places where C9 is too big and mini too subtle.

The wattage difference is not subtle

Look again at the incandescent row. A C9 bulb draws about 7 watts; a mini draws about 0.4. Seventeen times as much, per bulb.

Take a 60-foot roofline at 12-inch spacing — 60 bulbs:

  • Incandescent C9: about 420 watts.
  • LED C9: under 60 watts.

The continuous-load limit on a 15 amp, 120 V circuit is 1,440 watts. So three runs of incandescent C9 roofline is most of a circuit, and nothing else on that breaker gets a look in. The same three runs in LED use a tenth of the budget.

This single fact explains why almost all large outdoor displays are LED now, and it is worth knowing before you choose a size. A C9 display is the one where the choice between LED and incandescent genuinely changes what is possible, not just the bill. The full comparison is in LED versus incandescent.

Retrofit bulbs and empty socket wire

Worth knowing if you are planning a permanent roofline: C7 and C9 are also sold as separate screw-in bulbs plus bulk "socket wire" — plain cord with empty sockets at fixed spacing, cut to length.

That gives you two things a sealed string cannot. You pick your own spacing, and you replace one dead bulb instead of a whole string. The trade-off is that it costs more up front and takes an evening to assemble.

LED retrofit bulbs screw into the same C7 and C9 sockets as incandescents, so an existing socket-wire run can be converted a bulb at a time — one of the few situations where mixing is genuinely practical, as long as you convert a whole run rather than half of one. Half-converted, the colour difference will be obvious.

One practical caution on bulb sizes

C7 and C9 sockets are different sizes and the bulbs are not interchangeable. Both get casually described as "the big ones", and buying replacement bulbs without checking which you own is a common and annoying mistake. Measure one of your existing bulbs: seven eighths of an inch across is C7, just over an inch is C9.

Last reviewed November 2026.